Semi automatic flush
bolt OLDA 35 HZS
note. This product was previously called 35 HZ
Function:
Semi automatic, single action flush bolt for bolting of passive door leaf in double doors.
Features:
OLDA 35 HZS is bolted automatically when the passive door leaf closes but is unbolted manually. Forend width is 18 mm and the bolt is 15 x 17 mm.
Same dimensions as automatic flush bolts OLDA 34 HZA and OLDA 37 HZA.
One recommended combination – to achieve two bolting points in the door – is to fit 35 HZS at the top and 34 HZA at the bottom of the door leaf.
Manufactured in steel. Coating: electro zinc plating.
Usage:
To be recessed into doors of wood, steel or aluminium profiles without joint edges.
The bolt on 35 HZS is in its normal state projected to its full height. This leads to that the product, normally, only is recommended to be installed at the top in the edge of passive door leaves, also rebated.
At activation, when the passive door leaf closes, the bevelled bolt slides against the bottom of the lock plate and is retracted into the flush bolt, until the bolt reaches the hole in the lock plate and is projected again, at which point the bolting is complete. The unbolting is then made manually by using the finger grip.
If 35 HZS is to be fitted at the bottom, it must be ensured that the projected bolt does not collide with floor or sill etc.
Installation:
OLDA 35 HZS is fitted recessed in the edge of the door, either flush, with cut-out or without cut-out for the forend.
Fixed with four screws.
OLDA type 1 semi automatic flush bolt is fitted upper right in passive door leaf.
OLDA type 2 semi automatic flush bolt is fitted upper left in passive door leaf.
Accessories:
Lock plate LP 30 is developed for 35 HZS and can be turned (8, 10, 12 or 14 mm distance) to make it reach the edge and hence also work as a strike plate.
Specification:
- Semi automatic, single action bolt function
- Rectangular bolt:
- depth: 15 mm
- width: 17 mm
- projection: 14 mm
- adjustability: 0 mm
- Round electro zinc plated forend in steel
- Product:
- width: 18 mm
- height: 190 mm
- depth: 23/50 mm
- forend thickness: 3 mm
- Installation: in door leaf edge
- fixed with electro zinc plated screws, countersunk (rec. dim. 3,5×40 mm), 4 pcs.
- Accessories:
- Lock plate LP 30
- fastened with electro zinc plated screws, countersunk (rec. dim. 3,5×16 mm), 4 pcs.
- Lock plate LP 30
- Material: steel
- Coating: electro zinc plating
Product ID:
OLDA 35 HZS:
- type 1: 12-035-1000-11xx
- type 2: 12-035-2000-11xx
note. Accessories and screws for installation are ordered separately, or as a part of different product KITs.
Related products:
OLDA 34 HZA
– automatic flush bolt, also with forend width 18 mm
OLDA 37 HZA
– automatic flush bolt, also with forend width 18 mm, but with bolt for pre-load
Complementary products:
OLDA accessories for flush bolts
Also see:
Type of OLDA flush bolt – guide (pdf)
Documents:
product documents product leaflet pdf: 35 HZ type1 / 35 HZ type2 dimensions pdf: 35 HZS type1 / 35 HZS type2 installation - with forend cut-out: pdf: 35 HZS type1 / - without forend cut-out: pdf: 35 HZS type1 /
product views - 2D pdf: 35 HZS type1 / 35 HZS type2 dxf: 35 HZS type1 / 35 HZS type2 dwg: 35 HZS type1 / 35 HZS type2
product models - 3D stp: 35 HZS type1 / 35 HZS type2 igs: 35 HZS type1 / 35 HZS type2 dwg: 35 HZS type1 / 35 HZS type2 sat: 35 HZS type1 / 35 HZS type2 ipt: 35 HZS type1 / 35 HZS type2 stl: 35 HZS type1 / 35 HZS type2 pdf 3D: 35 HZS type1 / 35 HZS type2